ポジティブワン株式会社

以下は、LINバージョンによって若干異なることがあります。あくまで以下は参照レベルとしてください

物理レイヤー（Physical Layer Test）

CONDITIONS – CALIBRATION

• Operating Voltage Range
• Signal Threshold Voltages
• IUT as Receiver
• Variation of VSUP_NON_OP
• IBUS Under Several Conditions
• IBUS_LIM @ Dominant State ( Driver On )
• IBUS_Pas_dom : IUT in Recessive State
• IBUS_Pas_rec : IUT in Recessive State
• Slope Control
• Measuring the Duty Cycle @ 10.kBit/sec – IUT as Transmitter
• Measuring the Duty Cycle @ 20.0 kBit/sec – IUT as Transmitter
• Propagation Delay
• Propagation Delay of the Receiver
• GND / VBAT Shift Test - Dynamic
• GND Shift Test – Dynamic – IUT as Transceiver
• VBAT Shift Test – Dynamic – IUT as Transceiver
• Failure
• Loss of Battery
• Loss of GND

OPERATION MODE

Termination

• Measuring Internal Resistor – IUT as Slave
• Measuring Internal Resistor – IUT as Master
• Measuring Internal Capacitance – IUT as Slave

データーリンク層（Data Link Layer Test/NCNM）

タイミングパラメータ（TIMING PARAMETERS）

• Length of Synch Break Low Phase, IUT as Master
• Variation of Length of Synch Break Low Phase, IUT as Slave
• Length of Synch Break Delimiter, IUT as Master
• Variation of Length of Synch Break Delimiter, IUT as Slave
• Length of Header, IUT as Master
• Variation of Length of Header, IUT as Slave
• Oscillator Tolerance, IUT as Master
• Oscillator Tolerance, IUT as Slave without Making Use of Synchronization
• Oscillator Tolerance, IUT as Slave with Making Use of Synchronization
• Length of Frame, IUT as Slave Answering to a Master Request
•  IUT as Slave
•  IUT as Master with a Slave Task

COMMUNICATION WITHOUT FAILURE

• Variation of LIN Identifier
• IUT as Master
• IUT as Slave
• IUT as Master with Slave Task
• Transmission of the Checksum Byte
• IUT as Slave
• IUT as Master with Slave Task
• Extended Frame, Reserved , IUT as Slave
• Command Frame 'Master Request', IUT as Master
• Command Frame 'Master Request', IUT as Slave
• Command Frame 'Slave Response Frame, IUT as Master
• Command Frame 'Slave Response Frame', IUT as Slave
• Supported Frames According to the IUT Specification', IUT as Slave

COMMUNICATION WITH FAILURE

• Bit Error, IUT as Slave
• Checksum Error, IUT as Slave

EVENT TRIGGERED FRAMES

• Event Triggered Frame, IUT as Slave

ノードコンフィグレーションネットワーク・マネジメントテスト（NCNM）

STATUS MANAGEMENT

• Error in Received Frame, IUT as Slave
• Error in Transmitted Frame, IUT as Slave
• Error in Transmitted Frame with Collision, IUT as Slave

SLEEP / WAKE UP TESTS

• Send Command Frame 'Sleep Mode Command', IUT as Master
• Receive Command Frame 'Sleep Mode Command', IUT as Slave
• Receive a Wake Up Request, IUT as Master
• Receive a Wake Up Request, IUT as Slave
• Send a Wake Up Request
• IUT as Slave and Master with Slave Task
•  Send a Wake Up Request, No Following Frame Header from a Master, IUT as Slave
• Send a Wake Up Request, Frame Header from a Master Following, IUT as Slave
• Sleep Mode After Bus Idle

NODE CONFIGURATION

• Frame　ID　Assignment
• Frame ID Assignment – with Indirect Response
• Frame ID Assignment – with Direct Response
• LIN Product ID
• LIN Product ID – with Direct Response
• LIN Product ID – with Indirect Response
• Read by Identifier Command
• Read by Identifier Command with Correct NAD
• Read by Identifier Command with Incorrect NAD
• NAD Assignment
• NAD Assignment – Followed by ”Read by Identifier”
• NAD Assignment – with Positive Response
• Conditional Change NAD