Back
現在地: Home 
パートナー segger-tools Flasher PPC More
パートナー segger-tools Flasher PPC More
Flasher PPC More
Flasher PPC - Flash Programmer for PowerPC cores
Flasher PPC is a programming tool for PowerPC based microcontrollers with on-chip or external flash memory. Flasher PPC is designed for programming flash targets with the J-Flash software or stand-alone. It connects via Ethernet, USB or RS232 interface to a PC, running Microsoft Windows 2000, Windows XP, Windows 2003, Windows Vista or Windows 7.
Flasher PPC itself has a built-in 20-pin JTAG connector but is shipped with an 14-pin adapter for PowerPC devices.
Features
- Stand-alone JTAG programmer (Once set up, Flasher can be controlled without the use of PC program)
- Support for PowerPC cores
- Supports programming of internal and external flash memory
- 64 MB memory for storage of target program
- Host interfaces: Ethernet, USB, RS232
- Serial in target programming supported
- Data files can be updated via Ethernet/USB using J-Flash, via RS232 or via the mass storage functionality of Flasher PPC
- Target interface: JTAG
- No power supply required, powered through USB
- Programming speed up to 138 Kbytes/second depending on target hardware
Subscribe to Flasher PPC software notification Supported Devices
Currently, programming of the internal flash memory of the following devices is supported by Flasher PPC:
| Device | CPU core | Flash size [kBytes] |
|---|---|---|
| ST SPC560B40 | e200z0 (PowerPC) | 320 (256 KB Code flash + 64 KB Data flash) |
| ST SPC560B44 | e200z0 (PowerPC) | 448 (384 KB Code flash + 64 KB Data flash) |
| ST SPC560B50 | e200z0 (PowerPC) | 576 (512 KB Code flash + 64 KB Data flash) |
| ST SPC560C40 | e200z0 (PowerPC) | 320 (256 KB Code flash + 64 KB Data flash) |
| ST SPC560C44 | e200z0 (PowerPC) | 448 (384 KB Code flash + 64 KB Data flash) |
| ST SPC560C50 | e200z0 (PowerPC) | 576 (512 KB Code flash + 64 KB Data flash) |
| ST SPC560P40 | e200z0 (PowerPC) | 320 (256 KB Code flash + 64 KB Data flash) |
| ST SPC560P44 | e200z0 (PowerPC) | 448 (384 KB Code flash + 64 KB Data flash) |
| ST SPC560P50 | e200z0 (PowerPC) | 576 (512 KB Code flash + 64 KB Data flash) |
If your device is not listed here, please do not hesitate to get in touch with us: このメールアドレスはスパムボットから保護されています。閲覧するにはJavaScriptを有効にする必要があります。
Specifications
| General | |
|---|---|
| Supported OS | Microsoft Windows 2000 Microsoft Windows XP Microsoft Windows XP x64 Microsoft Windows 2003 Microsoft Windows 2003 x64 Microsoft Windows Vista Microsoft Windows Vista x64 Microsoft Windows 7 Microsoft Windows 7 x64 |
| Operating Temperature | + 5 °C ... + 60 °C |
| Storage Temperature | - 20 °C ... + 65 °C |
| Relative Humidity (non-condensing) | < 90% rH |
| Mechanical | |
| Size (without cables) | 121mm x 66mmx 30mm |
| Weight (without cables) | 119g |
| Available interfaces | |
| USB Host Interface | USB 2.0, full speed |
| Ethernet Host Interface | 10/100 MBit |
| RS232 Host Interface | RS232 9-pin |
| Target Interface | JTAG 20-pin (shipped with 14-pin adapter for Renesas PPC) |
| JTAG Interface, Electrical | |
| Power Supply | USB powered, 100mA for Flasher PPC. 500 mA if target is powered by Flasher PPC |
| Target interface voltage (VIF) | 1.2 ... 5V |
| Target supply voltage | 4.5V ... 5V (on the 14-pin adapter the target supply voltage can be switched between 3.3V and 5V) |
| Target supply current | max. 400mA |
| Reset Type | Open drain. Can be pulled low or tristated |
| Reset low level output voltage (VOL) | VOL <= 10% of VIF |
| For the whole target voltage range (1.8V <= VIF <= 5V) | |
| LOW level input voltage (VIL) | VIL <= 40% of VIF |
| HIGH level input voltage (VIH) | VIH >= 60% of VIF |
| For 1.8V <= VIF <= 3.6V | |
| LOW level output voltage (VOL) with a load of 10 kOhm | VOL <= 10% of VIF |
| HIGH level output voltage (VOH) with a load of 10 kOhm | VOH >= 90% of VIF |
| For 3.6 <= VIF <= 5V | |
| LOW level output voltage (VOL) with a load of 10 kOhm | VOL <= 20% of VIF |
| HIGH level output voltage (VOH) with a load of 10 kOhm | VOH >= 80% of VIF |
| JTAG Interface, Timing | |
| Max. JTAG speed | up to 12MHz |
| Data input rise time (Trdi) | Trdi <= 20ns |
| Data input fall time (Tfdi) | Tfdi <= 20ns |
| Data output rise time (Trdo) | Trdo <= 10ns |
| Data output fall time (Tfdo) | Tfdo <= 10ns |
| Clock rise time (Trc) | Trc <= 10ns |
| Clock fall time (Tfc) | Tfc <= 10ns |
JTAG interface connection (14-pin)
| Pin | Signal | Type | Description |
|---|---|---|---|
| 1 | TDI | Output | JTAG clock signal to target CPU. It is recommended that this pin is pulled to a defined state on the target board. Typically connected to TCK on target CPU. |
| 3 | TDO | Input | JTAG data output from target CPU. Typically connected to TDO on target CPU. |
| 5 | TCK | Output | JTAG clock signal to target CPU. It is recommended that this pin is pulled to a defined state on the target board. Typically connected to TCK on target CPU. |
| 7 | --- | NC | This pin is not connected to Flasher PPC. |
| 8 | --- | NC | This pin is not connected to Flasher PPC. |
| 9 | nRES | I/O | Target CPU reset signal. Typically connected to the RESET pin of the target CPU, which is typically called "nRST", "nRESET" or "RESET". |
| 10 | TMS | Output | JTAG mode set input of target CPU. This pin should be pulled up on the target. Typically connected to TMS on target CPU. |
| 11 | VDDE7 | Input | This is the target reference voltage. It is used to check if the target has power, to create the logic-level reference for the input comparators and to control the output logic levels to the target. It is normally fed from Vdd of the target board and must not have a series resistor. |
| 13 | nRDY | Input | Nexus ready output. Indicates to the development tools that the data is ready to be read from or written to the Nexus read/write access registers. |
| 14 | JCOMP | Output | JTAG TAP Controller Enable / JTAG Compliancy (JCOMP). JCOMP is used to enable the TAP controller for communication to the JTAG state machine for boundary scan and for debug access. This pin is set to HIGH by Flasher PPC (in order to enable the JTAG TAP controller on the target device). |
Notes:
- All pins marked NC are not connected to Flasher PPC. Any signal can be applied here; Flasher PPC will simply ignore such a signal.
- Pins 2, 4, 6, 12 are GND pins connected to GND in Flasher PPC. They should also be connected to GND in the target system.
Performance of MCUs with internal flash memory
The following table lists program and erase performance values for different controllers.
| Microcontroller | Size [kByte] | Erase time [sec] | Program time [sec] | Verify time [sec] | Total time [sec] |
|---|---|---|---|---|---|
| ST SPC560B50 | 576 | 4.747 | 4.159 | 1.929 | 10.917 |
